HP LaserJet 4200 Series Fuser Assembly-Exchange RM1-0013-230CN

PLEASE NOTE: This item is sold on an exchange basis.

In stock

Only 10 left

Part Number
RM1-0013-230CN-RX
$49.00

Description / HP LaserJet 4200 Series Fuser Assembly-Exchange RM1-0013-230CN

Product Information

HP LaserJet 4200 Series Fuser Assembly-Exchange

Part Number: RM1-0013-230CN-RX

Condition: Refurbished Exchange. Defective core return required.

Manufacturer / Brand: HP

110-127 V fuser assembly for the HP LaserJet 4200 series. The assembly bonds the toner image to the print media using heat and pressure.

Technical Specifications

Component typeFuser / fusing assembly
Listed part numberRM1-0013-230CN-RX
Electrical rating110-127 V
Printer familyHP LaserJet 4200 series
HP service referenceRM1-0013-000CN / RM1-0013-140CN
Alternate catalog part numbersRM1-0013-000CN, RM1-0013-140CN, Q2425-69017
FunctionBonds toner to paper using heat and pressure

Commonly Used to Fix

These manufacturer-documented checks are suggested repair paths. A code can have several causes; confirm the printer model, voltage and failed component before ordering.

Error code / light patternMeaning and applicable printer modelsChecks / how this part may fix it
50.1 FUSER ERRORLow fuser temperature
HP LaserJet 4200 series.
Switch the printer off and allow the fuser to cool. Check that the installed fuser matches the printer model and voltage. Reinstall it and inspect the connection; replace a damaged connector. If the error persists, replace the correct fuser. Continue with the dc controller PCA and then the power supply if the fault remains.
50.2 FUSER ERRORFuser warm-up service error
HP LaserJet 4200 series.
Switch the printer off and allow the fuser to cool. Check that the installed fuser matches the printer model and voltage. Reinstall it and inspect the connection; replace a damaged connector. If the error persists, replace the correct fuser. Continue with the dc controller PCA and then the power supply if the fault remains.
50.3 FUSER ERRORFuser over-temperature
HP LaserJet 4200 series.
Switch the printer off and allow the fuser to cool. Check that the installed fuser matches the printer model and voltage. Reinstall it and inspect the connection; replace a damaged connector. If the error persists, replace the correct fuser. Continue with the dc controller PCA and then the power supply if the fault remains.
50.4 FUSER ERRORFaulty fuser
HP LaserJet 4200 series.
Switch the printer off and allow the fuser to cool. Check that the installed fuser matches the printer model and voltage. Reinstall it and inspect the connection; replace a damaged connector. If the error persists, replace the correct fuser. Continue with the dc controller PCA and then the power supply if the fault remains.
50.5 FUSER ERRORIncorrect fuser installed
HP LaserJet 4200 series.
Switch the printer off and allow the fuser to cool. Check that the installed fuser matches the printer model and voltage. Reinstall it and inspect the connection; replace a damaged connector. If the error persists, replace the correct fuser. Continue with the dc controller PCA and then the power supply if the fault remains.
50.6 FUSER ERROROpen circuit in fuser
HP LaserJet 4200 series.
Switch the printer off and allow the fuser to cool. Check that the installed fuser matches the printer model and voltage. Reinstall it and inspect the connection; replace a damaged connector. If the error persists, replace the correct fuser. Continue with the dc controller PCA and then the power supply if the fault remains.
13.02.00 JAM IN TOP COVER AREAPaper did not pass the top-of-page sensor PS103 in time.
HP LaserJet 4200 series.
Clear jammed paper and scraps. Check that PS102 (pre-feed), PS103 (top-of-page), and PS108 (fuser delivery) sensor flags move freely. Check PS102 installation after paper-feed assembly replacement, PS103, and top-cover switch SW101. HP also lists fuser replacement and then dc-controller diagnosis if these checks do not resolve the jam. This code alone does not identify a failed fuser.
13.05.00 JAM IN TOP COVER AREAPaper did not reach the fuser-delivery sensor PS108 in time.
HP LaserJet 4200 series.
Clear jammed paper and scraps. Check that PS102 (pre-feed), PS103 (top-of-page), and PS108 (fuser delivery) sensor flags move freely. Check PS102 installation after paper-feed assembly replacement, PS103, and top-cover switch SW101. HP also lists fuser replacement and then dc-controller diagnosis if these checks do not resolve the jam. This code alone does not identify a failed fuser.
13.20.00 JAM IN TOP COVER AREAPaper was detected at power-on or initialization by PS102, PS103 or PS108.
HP LaserJet 4200 series.
Clear jammed paper and scraps. Check that PS102 (pre-feed), PS103 (top-of-page), and PS108 (fuser delivery) sensor flags move freely. Check PS102 installation after paper-feed assembly replacement, PS103, and top-cover switch SW101. HP also lists fuser replacement and then dc-controller diagnosis if these checks do not resolve the jam. This code alone does not identify a failed fuser.
13.21.00 JAM IN TOP COVER AREAThe top-cover switch SW101 opened during printing or may be defective.
HP LaserJet 4200 series.
Clear jammed paper and scraps. Check that PS102 (pre-feed), PS103 (top-of-page), and PS108 (fuser delivery) sensor flags move freely. Check PS102 installation after paper-feed assembly replacement, PS103, and top-cover switch SW101. HP also lists fuser replacement and then dc-controller diagnosis if these checks do not resolve the jam. This code alone does not identify a failed fuser.
13.06.00 JAM INSIDE REAR DOORA jam occurred in the rear delivery area.
HP LaserJet 4200 series.
Clear jammed media; inspect paper-width sensor PS106 and fuser-delivery sensor PS108 for freely moving flags. Check for scraps in the duplexer. HP lists PS106 and fuser replacement in the repair path. To isolate the duplexer, switch off, remove it, and switch on again; continue with dc-controller diagnosis if the problem persists.
13.12.00 JAM INSIDE REAR DOORA jam occurred in the rear delivery area.
HP LaserJet 4200 series.
Clear jammed media; inspect paper-width sensor PS106 and fuser-delivery sensor PS108 for freely moving flags. Check for scraps in the duplexer. HP lists PS106 and fuser replacement in the repair path. To isolate the duplexer, switch off, remove it, and switch on again; continue with dc-controller diagnosis if the problem persists.
13.1C.00 FUSER JAMMedia is wrapped around the fuser roller.
HP LaserJet 4200 series.
Switch off and allow at least 30 minutes for the fuser to cool before removal. Remove the fuser and turn its blue knob to release trapped media. Replace the fuser if necessary; remove all scraps before reinstallation.
41.3 UNEXPECTED SIZE IN TRAY XXLoaded media is longer or shorter than the configured tray size.
HP LaserJet 4200 series.
Correct the media size/type and verify tray settings on a configuration page first. Check PS102, PS103 and fuser-delivery sensor PS108 operation and free flag movement. A fuser-area obstruction or damaged delivery flag needs correction; this message alone does not justify buying a fuser. HP next lists the dc controller PCA if the fault persists.

Other Symptoms This Part May Fix

  • Wrinkles at the paper-path exit: Inspect the fuser inlet guide and pressure roller. A dirty inlet guide can require fuser replacement. Run cleaning pages for a dirty pressure roller; replace the fuser if the condition persists. Input-side wrinkles can instead originate in registration or feed rollers.
  • Toner smears or rubs off: Check media quality and fuser-mode settings and run cleaning pages. A defective fuser that does not heat sufficiently is a documented replacement path; the dc controller can also be responsible.
  • Specks or dots: Check the print cartridge, media and interior contamination. Worn fuser rollers are one documented cause that can require fuser replacement.
  • Dropouts or character voids: Check the paper side, media, environment, cartridge, density and EconoMode. Clean a dirty fuser using cleaning pages and check the fuser-mode setting before replacing parts.
  • Vertical or horizontal lines: Check the cartridge and laser path first. Clean a dirty fuser; replace it if lines persist. Damaged fuser film is a documented cause of horizontal lines.
  • Repeating defects or ghost images: Measure the repeat spacing and inspect the cartridge before choosing a part. HP identifies fuser repeats at 75.0 mm and 94.0 mm; 94.0 mm is specifically associated with the LaserJet 4300 fuser roller and is close to the cartridge drum repeat. Run cleaning pages; replace the fuser only when the defect is traced to it.
  • White lines or smudged lines: Inspect the cartridge, laser path and paper path. Clean the fuser and replace it if the diagnosed fuser defect persists; contamination or damage elsewhere must also be checked.
  • Curl or wave: Check media storage, room conditions, output bin and fuser-mode setting first. A setting change or different media/output path may correct curl without replacing the fuser.

Maintenance / Replacement Cycle

HP lists a 200,000-page expected component life and printer-maintenance interval for the original LaserJet 4200/4300 fuser. This is a service-planning reference, not a guaranteed yield for this replacement.

Run a cleaning page when replacing the print cartridge. Use copier-grade paper and select CONFIGURE DEVICE > PRINT QUALITY > CREATE CLEANING PAGE; follow the printed instructions. With a duplexer installed, open the rear output bin before cleaning and close it afterward. Automatic cleaning applies only without the optional duplexer; HP recommends 2,000 pages or less.

Switch off and allow at least 30 minutes for cooling before removing the fuser. Squeeze the blue release tabs and pull it straight out; fully seat the replacement until both sides snap into place. Reset the maintenance counter only after installing the complete maintenance kit.

Used In Products

HP LaserJet 4200L / 4200Ln
HP LaserJet 4200tn / 4200dtn / 4200dtns / 4200dtnsl

Warranty

90 days, provided by seller

More Information

Manufacturer HP
Condition Refurbished
Part Number RM1-0013-230CN-RX
OEM Part Number RM1-0013-230CN
Alternate Part Numbers RM1-0013-000CN, RM1-0013-230CN, RM1-0013-140CN, Q2425-69017
Weight 9.000000
Write Your Own Review
You're reviewing: HP LaserJet 4200 Series Fuser Assembly-Exchange RM1-0013-230CN

This form is protected by reCAPTCHA - the Google Privacy Policy and Terms of Service apply.

✓ FREE SHIPPING on Printer Parts Orders over $100 and Specified Toners within the continental USA