HP LaserJet 4200/4300 Stapler Stacker

All items come with standard warranty of 90 days, warranty provided by seller.

Out of stock

Part Number
Q2443B-RO
$195.00

Description / HP LaserJet 4200/4300 Stapler Stacker

Product Information

HP Q2443B Stapler/Stacker Assembly - Refurbished Outright

Part Number: Q2443B-RO

Condition: Refurbished Outright. No core return required.

Manufacturer / Brand: HP

Refurbished 500-sheet stapler/stacker for HP LaserJet4200 /4250 /4300 /4350 printers with the correct accessory configuration. Collects printed pages at the printer output and staples supported paper jobs.

Technical Specifications

Listed part numberQ2443B-RO
Component500-sheet stapler/stacker
HP product referenceQ2443B
HP service referenceQ2443-67908
Output capacity500sheets of75g/m2(20lb)paper; capacity varies with paper thickness/environment
Stacking media60-120g/m2paper;Letter,A4,Executive,Legal,B5(JIS),A5;custom148x210to216x356mm
Media routingDo not route envelopes or card stock to this output accessory
Stapling mediaLetter,A4orLegalpaper only
Maximum stapled job15sheets of75g/m2(20lb)paper; over-limit job prints unstapled with LEDcontinuously green
Stapler-unit service referenceRM1-1164-000CN
Staple-cartridge service referenceQ3216-60500; manufacturer catalog lists a3-pack of1000-staple cartridges
Staple-mode set size2-15sheets; maximum15sheets at75g/m2(20lb)

Commonly Used to Fix

These manufacturer-documented checks are suggested repair paths. Confirm the exact model, operating voltage and failed component before replacement.

Error code / light patternMeaning and applicable printer modelsChecks / how this part may fix it
13.12.09The optional output paper-inlet sensor has remained active too long. The accessory LED blinks amber.
HP LaserJet4200 /4250 /4300 /4350 with the correct optional output accessory; confirm its exact part number.
Use HELP and the arrow keys for the indicated jam-clearing instructions. Open the accessory jam-access door, remove all media and close it. Check that the indicated sensor lever and its spring move freely; reseat a displaced spring. Diagnose and correct printer faults first. Replace the correct output accessory only if the error persists after these checks and an accessory fault is confirmed. Inspect inlet sensor PS1101; verify the unit is installed and seated correctly.
13.12.10A page did not reach the optional output paper-inlet sensor in time. The accessory LED blinks amber.
HP LaserJet4200 /4250 /4300 /4350 with the correct optional output accessory; confirm its exact part number.
Use HELP and the arrow keys for the indicated jam-clearing instructions. Open the accessory jam-access door, remove all media and close it. Check that the indicated sensor lever and its spring move freely; reseat a displaced spring. Diagnose and correct printer faults first. Replace the correct output accessory only if the error persists after these checks and an accessory fault is confirmed. Verify that the printer output-bin deflector works correctly before replacing the accessory. The same condition is recorded as13.12.0A in the event log.
13.12.0A (event log)Event-log equivalent of displayed13.12.10; not a separate diagnosis.
HP LaserJet4200 /4250 /4300 /4350 with the correct optional output accessory; confirm its exact part number.
Use HELP and the arrow keys for the indicated jam-clearing instructions. Open the accessory jam-access door, remove all media and close it. Check that the indicated sensor lever and its spring move freely; reseat a displaced spring. Diagnose and correct printer faults first. Replace the correct output accessory only if the error persists after these checks and an accessory fault is confirmed. Check printer output deflector operation and the accessory inlet path; this is the same condition as displayed13.12.10.
13.12.11A jam was detected during accessory power-on. The accessory LED blinks amber.
HP LaserJet4200 /4250 /4300 /4350 with the correct optional output accessory; confirm its exact part number.
Use HELP and the arrow keys for the indicated jam-clearing instructions. Open the accessory jam-access door, remove all media and close it. Check that the indicated sensor lever and its spring move freely; reseat a displaced spring. Diagnose and correct printer faults first. Replace the correct output accessory only if the error persists after these checks and an accessory fault is confirmed. Empty the output bin and inspect the complete accessory path. The same condition is recorded as13.12.0B in the event log.
13.12.0B (event log)Event-log equivalent of displayed13.12.11; not a separate diagnosis.
HP LaserJet4200 /4250 /4300 /4350 with the correct optional output accessory; confirm its exact part number.
Use HELP and the arrow keys for the indicated jam-clearing instructions. Open the accessory jam-access door, remove all media and close it. Check that the indicated sensor lever and its spring move freely; reseat a displaced spring. Diagnose and correct printer faults first. Replace the correct output accessory only if the error persists after these checks and an accessory fault is confirmed. Empty the output bin and clear the accessory jam-access area before considering replacement.
13.XX.YY JAMManufacturer-documented grouped accessory-jam pattern. Confirm the jam is in this optional output device; the pattern alone does not identify a failed component.
HP LaserJet4200 /4250 /4300 /4350 with the correct optional output accessory; confirm its exact part number.
Use HELP and the arrow keys for the indicated jam-clearing instructions. Open the accessory jam-access door, remove all media and close it. Check that the indicated sensor lever and its spring move freely; reseat a displaced spring. Diagnose and correct printer faults first. Replace the correct output accessory only if the error persists after these checks and an accessory fault is confirmed. If no actual jam is visible, inspect inlet sensor PS1101 and delivery sensor PS1102 for a sticking or damaged lever. Replace the accessory only when its own fault remains.
56.2An unknown output device is installed.
HP LaserJet4200 /4250 /4300 /4350 with the correct optional output accessory; confirm its exact part number.
Turn the printer off and on. Reinstall the stacker or stapler/stacker and remove unsupported non-HP paper-handling devices. Confirm the exact compatible accessory and connector seating; this code alone does not prove the unit is defective.
66.00.15The output accessory was removed and replaced while printer power was on. Its LED is off in this documented condition.
HP LaserJet4200 /4250 /4300 /4350 with the correct optional output accessory; confirm its exact part number.
Turn printer power off, verify that the accessory is installed correctly and fully seated, then turn printer power on. Correct installation first; this event does not by itself establish a hardware failure.
Lower the optional binThe accessory output bin is raised. The LED blinks amber.
HP LaserJet4200 /4250 /4300 /4350 with the correct optional output accessory; confirm its exact part number.
Lower the output bin. If the message persists with the bin correctly positioned, the manufacturer directs replacement of the stacker or stapler/stacker.
OUTPUT BIN 1 FULLThe optional output bin is full; its LED blinks amber.
HP LaserJet4200 /4250 /4300 /4350 with the correct optional output accessory; confirm its exact part number.
Remove all paper from the bin. If the message persists, verify that the four plastic output flapper paddles move freely. A failed paper-full sensor PS1106 or driver PCA can require replacement of the accessory; an ordinarily full bin does not.
OUTPUT PAPER PATH OPENThe jam-access door or staple-cartridge door is open; the LED blinks amber.
HP LaserJet4200 /4250 /4300 /4350 with the correct optional output accessory; confirm its exact part number.
Close the indicated door. If the message persists with the doors correctly closed, inspect door-open switch SW1101 and the accessory driver PCA. Replace the accessory only for the persistent confirmed device fault.
LED blinking amberAccessory attention pattern associated with an output jam, raised/full bin or open paper path; it is not a unique component diagnosis.
HP LaserJet4200 /4250 /4300 /4350 with the correct optional output accessory; confirm its exact part number.
Read the printer display, clear the indicated jam, empty or lower the bin and close the correct door. Check sensor/door mechanisms before replacing the unit. Follow the matching exact display-code procedure.
13.12.07A staple-cartridge jam; the stapler did not complete stapling but returned home. LED blinks amber.
HP LaserJet4200 /4250 /4300 /4350 with the correct optional output accessory; confirm its exact part number.
Remove any jammed paper. Remove the staple cartridge, lift the green end door, remove the jammed staple, close the door and reinstall the cartridge and stapler unit. Replace a faulty staple cartridge first, then the stapler unit RM1-1164-000CN if necessary. If no jam is present and the driver PCA is defective, replacement of the complete stapler/stacker is the documented path.
13.12.08The output-bin page-detection sensor has remained active too long. This message applies to the stapler/stacker; LED blinks amber.
HP LaserJet4200 /4250 /4300 /4350 with the correct optional output accessory; confirm its exact part number.
Use HELP and the arrow keys for the indicated jam-clearing instructions. Open the accessory jam-access door, remove all media and close it. Check that the indicated sensor lever and its spring move freely; reseat a displaced spring. Diagnose and correct printer faults first. Replace the correct output accessory only if the error persists after these checks and an accessory fault is confirmed. Empty all pages from the output bin and clear the jam-access area. Replace the stapler/stacker only if the condition persists.
66.12.01Output-lift roller or paddle-motor error in the stapler/stacker; LED continuously illuminated amber.
HP LaserJet4200 /4250 /4300 /4350 with the correct optional output accessory; confirm its exact part number.
Use HELP, power off, verify correct installation and fully seated electrical connector, then power on. Inspect paddle mechanism/motor M1101. If the fault persists, replace the stapler/stacker as directed. This is not a fuser motor or printer main motor error.
66.12.02Jogger-motor error in the stapler/stacker; LED continuously illuminated amber.
HP LaserJet4200 /4250 /4300 /4350 with the correct optional output accessory; confirm its exact part number.
Use HELP, power off, verify installation and connector seating, then power on. Inspect the jogger mechanism/motor M1102. Replace the stapler/stacker if the confirmed fault persists.
66.12.03Stapler-motor error; LED continuously illuminated amber.
HP LaserJet4200 /4250 /4300 /4350 with the correct optional output accessory; confirm its exact part number.
Use HELP and power off before reseating the accessory. Verify correct installation and connector seating, then power on. Replace a failed stapler unit RM1-1164-000CN first; if the accessory driver PCA is faulty or the problem remains, replace the stapler/stacker as indicated.
STAPLER LOW ON STAPLESThe display table defines a low cartridge level as fewer than70staples. LED remains continuously green.
HP LaserJet4200 /4250 /4300 /4350 with the correct optional output accessory; confirm its exact part number.
Load the correct staple cartridge using the blue handle and latch the stapler unit closed. If the warning persists after following the replenishment instructions with a proper cartridge installed, replace the stapler unit. A confirmed driver-PCA fault is a separate manufacturer path to replacing the complete stapler/stacker.
STAPLER OUT OF STAPLESThe display table describes fewer than15staples remaining. LED blinks amber; behavior depends on STAPLES OUT setting.
HP LaserJet4200 /4250 /4300 /4350 with the correct optional output accessory; confirm its exact part number.
Replace the staple cartridge first. With STAPLES OUT=STOP, printing stops until replenished or SELECT is pressed; with CONTINUE, jobs print without stapling. If the condition persists, replace the stapler unit, followed by the complete stapler/stacker if necessary. Cartridge replenishment is not a reason to replace an otherwise working accessory.
LED continuously illuminated amberManufacturer-documented attention pattern for the stapler/stacker66.12.xx component faults; it is not a unique motor diagnosis.
HP LaserJet4200 /4250 /4300 /4350 with the correct optional output accessory; confirm its exact part number.
Read and preserve the exact printer display code. Power off, inspect installation and connectors, then follow the applicable66.12.01 paddle,66.12.02 jogger or66.12.03 stapler service sequence. Replace only the component or assembly identified by diagnosis.

Other Symptoms This Part May Fix

  • Recurring jams where paper enters or leaves the accessory: Correct printer faults first. Check media and environment; after a cold-to-warm move, remove condensation with a dry lint-free cloth or allow10-20minutes powered on before testing. Inspect the feed motor/rollers, inlet sensor PS1101 and delivery sensor PS1102 for free lever/spring movement. Clean dirty rollers, reseat displaced springs and replace the accessory only for a confirmed persistent accessory fault. If the leading edge has not emerged from the printer, inspect the deflector and its printer-side solenoid; a failed printer deflector mechanism requires its own repair.
  • Skew or a bent leading edge caused inside the optional output path: Clean contamination from the accessory path, inspect feed guides and clean dirty rollers. If worn rollers or damaged guides in the output device remain, the manufacturer lists accessory replacement. Skew originating in the printer registration or input path is a separate fault.
  • No accessory power: With printer power off, inspect and fully seat the unit and its connector. If it was installed while powered on, turn the printer off and on after correct seating. A confirmed defective accessory driver PCA can require replacement of the output device.
  • No stapling despite completed printing: Set CONFIGURE DEVICE > STAPLER STACKER > STAPLES to ONE. Refill staples, use one paper size per job and use2-15sheets within the75g/m2(20lb)rating. A defective stapler unit can require RM1-1164-000CN replacement; a failed accessory driver PCA can require the complete stapler/stacker. Settings, unsupported/mixed-size media and an empty cartridge are separate causes.
  • Testing output transport and stapling: Set CONFIGURE DEVICE > STAPLER STACKER > STAPLES to ONE, then exit using PAUSE/RESUME or MENU. Select DIAGNOSTICS > PAPER PATH TEST > DESTINATION > OPTIONAL BIN1; set COPIES to10, then PRINT TEST PAGE. The documented test sends10pages to the unit for stapling. Check printer/driver optional-output configuration before diagnosing hardware.

Maintenance / Replacement Cycle

Reload staples when prompted: rotate the stapler unit toward the printer front until it clicks open, pull the old cartridge out by its blue handle, insert the replacement cartridge, then rotate the unit back until it snaps into place. Replenishment is condition-based; no fixed service life for this complete refurbished accessory is claimed.

Used In Products

HP LaserJet 4300 series
HP LaserJet 4250 series
HP LaserJet 4350 series

Warranty

90 days, provided by seller

More Information

Manufacturer HP
Condition Refurbished
Part Number Q2443B-RO
OEM Part Number Q2443B
Alternate Part Numbers Q2443B
Weight 9.600000
UPC/EAN 829160306964
Write Your Own Review
You're reviewing: HP LaserJet 4200/4300 Stapler Stacker

This form is protected by reCAPTCHA - the Google Privacy Policy and Terms of Service apply.