HP LaserJet 4250/4350 Duplex Feeder - New Open Box
Description / HP LaserJet 4250/4350 Duplex Feeder - New Open Box
Product Information
HP Q2439B Duplexer Assembly - New Open Box
Part Number: Q2439B-NO
Condition: New Open Box
Manufacturer / Brand: HP
Automatic two-sided printing accessory for HP LaserJet 4250 / 4350 printers. Match the exact Q2439B unit and printer configuration before replacement.
Technical Specifications
| Listed part number | Q2439B-NO |
|---|---|
| Component | Automatic duplexer assembly |
| HP product reference | Q2439B |
| HP documented service reference | Q2439-67902 |
| Function | Automatic two-sided printing and paper reversal |
| Supported paper | 60-120 g/m²(16-32 lb);Letter, A4, Executive, Legal, B5(JIS), A5 |
| Media/output requirements | Face-up rear bin closed; do not duplex envelopes, labels, transparencies or card stock |
Commonly Used to Fix
These manufacturer-documented checks are suggested repair paths. Confirm the exact model, operating voltage and failed component before replacement.
| Error code / light pattern | Meaning and applicable printer models | Checks / how this part may fix it |
|---|---|---|
| BAD DUPLEXER CONNECTION | The duplexer is not functioning. HP LaserJet 4250 / 4350 with the matching Q2439B duplexer. | Turn printer power off, remove and reinstall the duplexer, turn power on and inspect the rear accessory power connection. Correct installation or a printer-side connector fault first. If the error persists and the duplexer is faulty, the manufacturer directs duplexer replacement. |
| REINSERT DUPLEXER | The duplexer is not functioning or its connection must be reseated. HP LaserJet 4250 / 4350 with the matching Q2439B duplexer. | Turn printer power off, remove and reinstall the duplexer, turn power on and inspect the rear accessory power connection. Correct installation or a printer-side connector fault first. If the error persists and the duplexer is faulty, the manufacturer directs duplexer replacement. |
| CANNOT DUPLEX Check rear bin | The printer cannot perform duplex printing. The face-up rear output bin must be closed. HP LaserJet 4250 / 4350 with the matching Q2439B duplexer. | Close the face-up rear bin before sending the duplex job. If a hardware fault persists, the documented replacement sequence is the duplexer followed by the DC controller. A bin left open is an operating condition, not proof that the unit is defective. |
| CANNOT DUPLEX Check paper | The printer cannot perform duplex printing with the current paper/path condition. HP LaserJet 4250 / 4350 with the matching Q2439B duplexer. | Use supported duplex media and close the face-up rear bin. If the condition persists after these checks, the manufacturer lists duplexer replacement, then the DC controller. Settings or unsuitable paper require correction rather than a new unit. |
| 13.XX.YY DUPLEX JOB INTERRUPTED | The duplex job was physically interrupted, often when someone grasped a sheet temporarily protruding during reversal. HP LaserJet 4250 / 4350 with the matching Q2439B duplexer. | Follow HELP and the displayed instruction to discard the top one or two sheets as specified, then press SELECT to continue. Do not remove the page until duplex printing finishes. If a genuine hardware fault persists, the manufacturer lists the duplexer, then the DC controller. With JAM RECOVERY=OFF, resend any missing pages because they might not be reprinted. |
| 13.13.00 | A page is jammed inside the duplexer. HP LaserJet 4250 / 4350 with the matching Q2439B duplexer. | Use HELP, clear the jam and check for small torn scraps inside the duplexer. Power off, remove the duplexer and power on; if the error persists without the unit, the manufacturer directs DC-controller replacement. The duplexer itself is the subsequent documented replacement step when diagnosis identifies it. |
| 13.06.00 | A page is jammed near the rear output door; the duplexer is one area to inspect. HP LaserJet 4250 / 4350 with the matching Q2439B duplexer. | Clear the jam. Check the paper-width/fuser-delivery sensors PS106/PS108 and free sensor-arm movement; remove torn scraps from the duplexer. The documented printer-side path includes the media-size sensor and fuser. Power off and remove the duplexer to isolate the fault; an error that persists without it points toward the DC controller. This unit is a suggested repair only if diagnosis confirms its own rollers, gears, guides, sensors or belt are faulty; it does not repair a failed fuser or printer sensor. |
| 13.12.00 | A page is jammed near the rear output door; distinguish duplex-path damage from printer sensor/fuser faults. HP LaserJet 4250 / 4350 with the matching Q2439B duplexer. | Clear media and check PS106/PS108, free sensor movement and scraps inside the duplexer. Follow the separate printer sensor/fuser checks before replacing the duplexer. Power off, remove the unit and retest to isolate the fault; if it persists without the duplexer, follow the DC-controller path. Replace this unit only for a confirmed fault within its own duplex path. |
| 57.7 | Duplexer cooling-fan error. HP LaserJet 4250 / 4350 with the matching Q2439B duplexer. | Turn the printer off and on. If the fault remains, the manufacturer directs duplexer replacement. Confirm the exact matching unit; a different printer cooling fan is a separate part. |
| 13.XX.YY JAM | Manufacturer grouped jam pattern; this row applies only when the problem is isolated to the duplex path. HP LaserJet 4250 / 4350 with the matching Q2439B duplexer. | Compare simplex and duplex jobs and clear actual media scraps first. Inspect oblique rollers/gears, feed guides, sensors and belt in the duplexer. The manufacturer lists duplexer replacement for defective oblique rollers/gears, feed guide or sensors; a cut/sagging belt, failed reversing motor or damaged guide may have a separate component repair. Confirm the fault location before ordering the complete unit. |
Other Symptoms This Part May Fix
- Jams that occur only while duplexing: Compare simplex and duplex jobs using correctly stored supported paper, and do not grab the page while it is reversing. Inspect oblique rollers and their drive gears, the duplex feed guide, sensors and internal belt. The manufacturer directs unit replacement for defective rollers/gears, guide or sensors. A cut/sagging belt, failed reversing motor or burr-damaged guide can require its own component repair; remove any foreign material first. A printer DC-controller fault is a separate cause.
- Isolating an intermittent duplex-path jam: Use DIAGNOSTICS > PAPER PATH TEST and select the installed source, destination and DUPLEX option. Choose the appropriate copy count; the documented choices are1, 10, 50, 100 or 500. Select PRINT TEST PAGE and compare simplex versus duplex results. Correct media, settings or printer-side faults before replacing the accessory.
Used In Products
Warranty
90 days, provided by seller
More Information
| Manufacturer | HP |
|---|---|
| Condition | New |
| Part Number | Q2439B-NO |
| OEM Part Number | Q2439B |
| Alternate Part Numbers | Q2439B, Q2439-69003 |
| Weight | 9.000000 |
| UPC/EAN | 829160306100 |
Write Your Own Review